top of page

Clamp-On Leak Surveys: Convert Cut-Off Velocity into a Flow Limit

6 days ago
4 min read

A clamp-on flow survey can show zero while a small flow remains below a configured cut-off. Before reporting “no leakage detected”, translate any velocity-based cut-off into a volumetric flow for the actual pipe bore. The same velocity setting represents very different litres per minute in a small branch and a large main. That calculation defines a configuration limit; it does not establish the installation’s measurement accuracy.


Establish what the setting actually does


Holykell’s handheld flow-meter manual identifies M41 as the low-flow cut-off and explains that readings whose absolute magnitude is below the setting are replaced by zero. It describes zero adjustment separately in M42. This is a documented example, not proof that every handheld meter or firmware uses the same menus, units or processing path.



On the supplied instrument, confirm whether the threshold is expressed as velocity or volumetric flow, its current value and units, and which outputs it affects. Photograph the setting and record the manual revision. Do not assume the display, totaliser, pulse output and downloaded record all apply identical rules.


ProSense’s pictured ProSight handheld ultrasonic flow meter is offered for portable pipe surveys. The real catalogue photograph shows a demonstration arrangement, not a validated leak test or evidence of the minimum flow measurable at a customer site.


Orange handheld ultrasonic flow meter held beside two transducers clamped to a white pipe in a catalogue demonstration photograph.
ProSight handheld ultrasonic flow meter with externally clamped transducers. ProSense catalogue demonstration photograph; not a customer installation or evidence of site performance.


Convert velocity using the internal diameter


For a full circular pipe, volumetric flow is mean velocity multiplied by internal cross-sectional area: Q = v × π × D² / 4. Use D in metres and v in metres per second to obtain Q in cubic metres per second. Multiply by 3,600 for cubic metres per hour, or by 60,000 for litres per minute.


Use the actual internal diameter, including the effect of wall thickness and any liner. Nominal pipe size and outside diameter are not interchangeable with the bore. Keep the diameter source with the calculation, and avoid presenting an uncertain bore as an exact value.


Hypothetical example: assume an independently established 100 mm internal diameter and a velocity cut-off of 0.03 m/s. These are illustrative inputs, not a recommended setting or a verified default for the pictured instrument. The area is approximately 0.007854 m². The corresponding flow is 0.0002356 m³/s, or about 0.848 m³/h and 14.1 L/min.


A hypothetical 5 L/min flow is below that configuration threshold. A zero display under those assumptions cannot rule it out. At 200 mm internal diameter, the same velocity threshold corresponds to about 56.5 L/min, because doubling diameter multiplies area by four. Always recalculate when moving a portable instrument to another pipe.


Keep configuration limits separate from measurement capability


A calculated cut-off flow is not a guaranteed detection limit. Lowering a setting cannot establish that the acoustic installation can reliably resolve every smaller flow. The selected transducers, pipe data, liquid, mounting and signal quality still need verification against the exact product documentation and application.


Nor does a long observation automatically solve the problem. If small readings are being replaced by zero before storage or accumulation, simply extending the survey may preserve more zeros. Confirm the documented data path instead of assuming that the totaliser will reveal what the display suppresses.


Plan an authorised low-flow check


First define the smallest flow that matters to the investigation, its likely duration and the evidence required to distinguish it from measurement uncertainty. Record both the engineering requirement and the current cut-off expressed in the same units. If the threshold exceeds the required flow, resolve that mismatch before accepting the survey method.


Next establish suitable measurement conditions and retain the available diagnostics. Use normal operating observations or a controlled test agreed with the responsible team. Where a known flow is required, arrange an appropriate reference method and account for its uncertainty; a pump command or valve position alone does not prove a particular flow.


Change a setting only within the exact manual’s permitted procedure and the site’s authorisation. Save the baseline, change one item at a time and record the resulting diagnostics and observations. Do not adjust zero while assuming that an apparently closed valve guarantees stopped flow. Do not manipulate operating equipment merely to produce a preferred reading.


Write a defensible survey conclusion


Report the pipe bore and its source, instrument identification, transducers, cut-off value and units, calculated equivalent flow, observation period and measurement-quality evidence. State which display or output was assessed. Record any configuration changes and restoration.


Avoid treating “zero throughout the survey” as a universal no-leak certificate. A more useful conclusion identifies the conditions observed and the flows the arrangement could not confidently assess. This survey does not locate a leak, prove isolation integrity or establish a certified protective function.


For help planning a low-flow survey, send ProSense the pipe material, outside diameter, wall and liner details, liquid, expected operating range, smallest flow of interest and required recording method. Ask for the supplied unit’s cut-off units and low-flow suitability to be confirmed before choosing the test configuration.


Need help with your application?


ProSense Instruments - explore instruments, sensors, data loggers and test equipment.


ProSense Solutions - discuss complete monitoring and automation systems.


ProSight Software - explore cloud dashboards, alarms and reporting. Device integration must be confirmed for your application.



Project enquiries: sales@prosense.com.au. Software enquiries: info@prosightsoftware.com.

Comments


bottom of page